Repairs to uPVC Windows

uPVC is a great option for modern homes. They are long-lasting, durable and easy to maintain. They are not susceptible to decay or rust as aluminum and timber.

It is important to clean and oil UPVC doors and windows regularly. This will save you from unnecessary repair costs and also improve energy efficiency.

1. Broken Glass

If the glass in your window is broken it can cause a huge deal of damage to your home, which can make it very hazardous and possibly fatal. It is important to ensure that your windows are in good condition.

For single pane windows, it is fairly easy to replace windows, and the new one will usually fit inside the frame that was previously installed easily. If you have double-paned windows that are held together by internal beading, it will be more difficult to remove and replace the panes that were previously in use. In this situation it is essential to buy plastic spacers to aid in fitting the new pane into the window frame.

If you plan to attempt to remove the window panes yourself, it is essential to wear the appropriate safety equipment that includes gloves with a thick layer of material and eye protection. It is also recommended to lay down a drop cloth before you begin working on the window panes so that any shards fall on the fabric and not on the floor, where they could be trampled.

It's a good idea to cover the gap with tape after the glass is removed. This will prevent water and drafts from entering your home until a professional comes out to fix the window. This will also act as a barrier, deterring any intruders from getting access into your home. If the gap between the window and the door is significant, you may want to use a security screen that also has windows. This will give you the best of both.

2. Sagging

uPVC windows and doors are an affordable, durable and energy-efficient alternative to timber sash windows. However, over time, they are susceptible to a range of issues, including sagging. A window that isn't properly aligned can cause problems with light, double glazing repair Bromley draughts or even security. If you find that your uPVC window is beginning to lose its shape, it's crucial to act fast to prevent the problem from becoming worse.

To fix a window repairs Rushden that is sagging you can try repositioning the hinges. To do this, you'll have to open the window so that you can access the frame. Then, remove both the top and bottom hinges using a screwdriver and adjust the hinges clockwise or counter-clockwise. After you've repositioned the hinges, shut your window and check for fitting. If you're satisfied with the fit of the window, you can tighten screws to keep them in the right position.

If you are unable to reposition the hinges you may need to replace the seal. Over time, rubber seals lose their elasticity and become dry, which causes them to loosen. If this happens, it's crucial to replace the seal as soon as possible to ensure your uPVC windows remain watertight and safe from drafts.

UPVC handles can also loosen. The majority of the time this is due to screws that have come loose over time. However, it can be due to the fact that the handle mechanism has worn out. Fortunately, it's easy to repair the loose uPVC window handle yourself. First, you'll need to close the window and then perform an experiment fitting. The joint at the corners of the sash must align with the joint on the casing. If it isn't, you can make use of a screwdriver to loosen the handle, and then return the mechanism to its original the position it was in.

3. Water Leaks

It is important to take action if get up each morning to find mouldy walls and wet floors. The leaks of water through windows could cause structural damage to your home, and affect your ability to regulate the temperature of your home. The most frequent reason for leaks in uPVC windows is that the sealant surrounding the frame is damaged or not present.

This is a fairly simple fix and should be undertaken by any DIY expert. Based on the severity of the issue the caulking that was used up may need to be removed before a fresh layer is applied. It is essential to remember that when it is about uPVC window repairs you should avoid the temptation to "over-caulk and then make the area harder to clean and reduce the efficiency of your energy.

It is crucial to make sure that the drainage holes are free of debris and that the sill pan is placed in a way that allows it to drain away from the window. In more serious cases you might need to consider replacing the window.

Other signs of long-term water leakage are rotted sills and the appearance of black spots of mold on the wall near the window. The fungus thrives in damp conditions and can quickly spread throughout the house.

It is also important to remember that if the leakage originates from the glass in your Double Glazing Repair Bromley glazed windows, it's more likely to be an issue with the glass seal, rather than the frame or sliding. Again this can easily be corrected by an uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges may be to blame when your uPVC window is difficult to open or it opens with an ease. These are easily replaced by any competent DIYer and can usually be done within a few minutes.

Like any mechanical component, hinges can wear out over time. It's easy to change a window hinge but it's much easier if someone helps you to hold the frame.

It is also worth checking that the uPVC hinges are opening and closed in the right direction. Look for the arrows that are on each hinge to determine the direction in which the window should be opened.

The issue can be caused by opening the window incorrectly or by a poor installation at the factory. Sending us a picture through our website can often resolve the problem. We are always happy to give suggestions.

It is also important to lubricate the hinges regularly. Applying an engineering lubricant that is light to the hinges is a great way to do this. We recommend using an oil that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It can also lower the risk of a window getting stuck and stop corrosion. This must be done at a minimum every year. WD40 and other solvent based lubricants are not recommended as they will damage parts of your uPVC window.

5. Draughts

Draughts can be caused by several different causes. Firstly the hinges, again because of wear and tear, may become displaced, which causes a gap to form where the sash joins the frame. They can be fixed by giving them a good clean, but when they're beyond repair, it might be necessary to get them realigned or replaced. In addition, the interlock could also become disaligned. This happens on the hinge's side and might require to be cleaned. In some cases it is possible to replace the hinges.

The seals may wear out or be damaged over time, allowing air escape. Installing high-quality weatherstripping is a good way to prevent draughts. Replace the windows made of upvc with low-emissivity glass. This will help control indoor temperatures and decrease the risk of draughts.

One of the most effective methods to reduce draughts is by using a draught excluder, these are usually fabric tubes filled with some kind of filler. They can be positioned on the top of your windowsill. They will keep your home warm by blocking out cold air.

The windows made of upvc can continue to provide excellent insulation and security for your home with a little regular maintenance and repairs. However, it is important to realize that windows last for a certain period of time and there may come a point where it is more efficient to replace them than fix them. If you are experiencing problems with your upvc windows, it is best to seek professional assistance as soon as you can.